Index: pykota/trunk/pykota/accounters/hardware.py
===================================================================
--- pykota/trunk/pykota/accounters/hardware.py (revision 2146)
+++ pykota/trunk/pykota/accounters/hardware.py (revision 2147)
@@ -20,126 +20,4 @@
 #
 # $Id$
-#
-# $Log$
-# Revision 1.36  2005/02/20 22:58:55  jalet
-# Added some informations from RFC3805 and RFC2790
-#
-# Revision 1.35  2005/01/12 22:44:06  jalet
-# Tried to fix a problem with printers which are slow to pass into printing mode.
-#
-# Revision 1.34  2004/11/19 11:57:51  jalet
-# Modified the SNMP fix as hinted by pysnmp's maintainer
-#
-# Revision 1.33  2004/11/19 10:35:37  jalet
-# Catches TypeMismatchError in SNMP answer handling code
-#
-# Revision 1.32  2004/11/16 23:23:40  jalet
-# Fixed internal PJL handling wrt the 35078 PowerSave mode.
-#
-# Revision 1.31  2004/11/01 14:32:26  jalet
-# Fix for unneeded out of band status in pjl_over_tcp/9100
-#
-# Revision 1.30  2004/10/05 09:21:34  jalet
-# Removed misleading comments
-#
-# Revision 1.29  2004/10/05 09:20:07  jalet
-# Reduced delay from 2 to 1 seconds in internal SNMP and PJL_over_TCP
-# handlers
-#
-# Revision 1.28  2004/09/27 20:09:30  jalet
-# Lowered timeout delay for PJL queries
-#
-# Revision 1.27  2004/09/27 20:00:35  jalet
-# Typo
-#
-# Revision 1.26  2004/09/27 19:56:27  jalet
-# Added internal handling for PJL queries over port tcp/9100. Now waits
-# for printer being idle before asking, just like with SNMP.
-#
-# Revision 1.25  2004/09/27 09:21:37  jalet
-# Now includes printer's hostname in SNMP error messages
-#
-# Revision 1.24  2004/09/24 21:19:48  jalet
-# Did a pass of PyChecker
-#
-# Revision 1.23  2004/09/23 19:18:12  jalet
-# Now loops when the external hardware accounter fails, until it returns a correct value
-#
-# Revision 1.22  2004/09/22 19:48:01  jalet
-# Logs the looping message as debug instead of as info
-#
-# Revision 1.21  2004/09/22 19:27:41  jalet
-# Bad import statement
-#
-# Revision 1.20  2004/09/22 19:22:27  jalet
-# Just loop in case a network error occur
-#
-# Revision 1.19  2004/09/22 14:29:01  jalet
-# Fixed nasty typo
-#
-# Revision 1.18  2004/09/21 16:00:46  jalet
-# More informational messages
-#
-# Revision 1.17  2004/09/21 13:42:18  jalet
-# Typo
-#
-# Revision 1.16  2004/09/21 13:30:53  jalet
-# First try at full SNMP handling from the Python code.
-#
-# Revision 1.15  2004/09/14 11:38:59  jalet
-# Minor fix
-#
-# Revision 1.14  2004/09/14 06:53:53  jalet
-# Small test added
-#
-# Revision 1.13  2004/09/13 16:02:45  jalet
-# Added fix for incorrect job's size when hardware accounting fails
-#
-# Revision 1.12  2004/09/06 15:42:34  jalet
-# Fix missing import statement for the signal module
-#
-# Revision 1.11  2004/08/31 23:29:53  jalet
-# Introduction of the new 'onaccountererror' configuration directive.
-# Small fix for software accounter's return code which can't be None anymore.
-# Make software and hardware accounting code look similar : will be factorized
-# later.
-#
-# Revision 1.10  2004/08/27 22:49:04  jalet
-# No answer from subprocess now is really a fatal error. Waiting for some
-# time to make this configurable...
-#
-# Revision 1.9  2004/08/25 22:34:39  jalet
-# Now both software and hardware accounting raise an exception when no valid
-# result can be extracted from the subprocess' output.
-# Hardware accounting now reads subprocess' output until an integer is read
-# or data is exhausted : it now behaves just like software accounting in this
-# aspect.
-#
-# Revision 1.8  2004/07/22 22:41:48  jalet
-# Hardware accounting for LPRng should be OK now. UNTESTED.
-#
-# Revision 1.7  2004/07/16 12:22:47  jalet
-# LPRng support early version
-#
-# Revision 1.6  2004/07/01 19:56:42  jalet
-# Better dispatching of error messages
-#
-# Revision 1.5  2004/06/10 22:42:06  jalet
-# Better messages in logs
-#
-# Revision 1.4  2004/05/24 22:45:49  jalet
-# New 'enforcement' directive added
-# Polling loop improvements
-#
-# Revision 1.3  2004/05/24 14:36:40  jalet
-# Revert to old polling loop. Will need optimisations
-#
-# Revision 1.2  2004/05/18 14:49:22  jalet
-# Big code changes to completely remove the need for "requester" directives,
-# jsut use "hardware(... your previous requester directive's content ...)"
-#
-# Revision 1.1  2004/05/13 13:59:30  jalet
-# Code simplifications
-#
 #
 #
